Release Notes/Solved items Version 2019.1

RadiMation version 2019.1.6

• #7305: Communication with the TDEMI should be optimized for Continuous Measurement
• #9669: Extend Gauss Instruments TDEMI driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #10043: EM-Test NX5: Selected line coupling is not possible.
• #10053: Exception has been thrown by the target of an invocation.
• #10054: AD converter limit lines not visible in time graph.
• #10098: Object reference not set to an instance of an object, when editing a non existing cable.
• #10105: powersensors not recognized HP438
• #10110: Make sure that using |||| in the report generator is correctly handled and does not trigger a infinite loop.
• #10121: Voltage dips and interupts: Sequence not starting at number 1.
• #10124: VDI - When a test is closed it is not possible to change the settings Test failed/passed
• #10125: Sequence order disfunction.
• #10126: R&S ESR7 - Preamplifier gets always inactive when starting a measurement
• #10127: RI: Band is shown in report as 43,567 Ghz while it was 1Ghz in test.
• #10141: EUT calibration-Attenuation/Gain: Limitlines are not exported.
• #10175: Internal frequency correction of DARE!! RadiSense 10 probe should by default be off
• #10176: Graphs: Setting a default for a line is not loaded correctly upon starting a new test.
• #10189: 17-03 Prana SX 120-100 low: Amplifier has not correctly set the desired range.
• #10199: Value cannot be null.
• #10214: Driver: EMSense 10
• #10232: Auto scale height graph.
• #10277: De objectverwijzing is niet op een exemplaar van een object ingesteld.
• #10278: Hewlett Packard 8563A: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO).
• #10279: Rohde & Schwarz ESR 26 Input 2 Scanning Receiver: Specific System Error: -222,"Data out of range; :SCAN1:STAR 0 HZ
• #10289: CI: Stepsize in the test does not mach the stepsize setting in 2019.1.5.
• #10398: Icon now correctly displays status pass/fail

RadiMation version 2019.1.5

• #8672: Limit line file printout shows no units in the table for Frequency and Value.
• #9259: HTTPS version of RADIWIKI site
• #9519: SMR 4503: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #9529: emtest UCS 00N: One or several values are limited by the simulator. The paremeters are set to a minimum
• #9888: Agilent 8753: Specific System Error: 50 , "CAUTION: TOO MANY SEGMENTS OR POINTS""
• #9925: Reporting in Excel not functioning well in 2019.1.2
• #9945: Driver: R&S NRX
• #9970: DARE!! Instruments RSS2010I: Device stream is not connected
• #9971: Schlöder SFT 1400: An unexpected unit code is returned. Is another Schloeder model connected?
• #10014: Radiated Emission Tower does not stop
• #10045: Activate HTTPS support for HelixALM website
• #10052: Keysight Technologies DSOX4154A
• #10082: Rounded frequency steps.
• #10099: Device specific setting in the RPR3006W for 'Edge Fall Time'
• #10109: "|| TEMPERATURE ||" exports wrong string
• #10115: Switch matrix sends scientific notation numbers
• #10119: EM-Test Compact NX5 VDIP - checkered flag not visible after test
• #10148: Pulsed immunity EFT Multiband - Export icons pass are not consistent.
• #10156: CI: Forward power reads 40 db too high
• #10159: RadiMation 2019.1.4 using a fixed min and max for Y axis does not work anymore.
• #10160: 1GHz radiated EMI: Amplitude scale not automatically adjusted.
• #10161: CI- 2019.1.4 does not output the time column in the report generator anymmore
• #10163: Gauss Instruments TDEMI: Invalid parameter value.
• #10169: When logging the results of the CW measurements in the multiband method, the line-wise assignment between frequency and signal power and / or output power is not correct! The same applies to the documentation of the Apparent Power
• #10170: The graphs for harmonic and compression power measurements are incorrectly formatted. This may be due to the incorrect designation of the frequency axis (Hz instead of MHz).
• #10174: Graphs: Fixed limits are scaling instead of being fixed.
• #10179: VDI Repetition time is cut when changing angle for UCS500
• #10187: Exporting Electrical field probe line as cal file not possible
• #10191: Rohde & Schwarz ESPI 3 Scanning Receiver: Specific System Error: -222,"Data out of range; :FREQ:STOP 9000 HZ"
• #10193: Index out of bounds when showing polar plot.
• #10194: Lock timeout on etherds
• #10195: Height Graph: Height plot: Max Peak for peak 1 not drawn in graph.
• #10233: Updated the manual to reflect the current UI for cables
• #10229: DARE!! Instruments RPR3006W: Wrong command
• #10230: Resolves IDN check issue with 30S1G3
• #10244: RadiMation not responding - freezes
• #10250: Saving TSF in directory crash, and TSF seemingly lost
• #10256: ESRP 7 Scan max min only usable in scanmode
• #10261: Analyser: Gauss TDEMI 9 Wrong RBW 9-150 kHz QP scan
• #10314: Some graphlines are displayed multiple times in the default Custom Graph window
• #10329: TDEMI M6+ is much slower with Radimation then doing the test manualy
• #10332: Ability to use the R&S ESW with more than 32000 points
• #10337: How can we directly control level of injection current in CI & How can we set the level of field strength in RI

RadiMation version 2019.1.4

• #7991: VDI Repetition time is cut when changing angle for PSF500
• #8086: R&S ESW26 abillity to set number of points on X-axis
• #9559: RF Amplifier (ID1344): Prana returned a warning state.
• #9774: CE No trace when using 200 Hz RBW and a 3 Khz VBW
• #10011: When opening an EUT file the directory should be set to the EUT directory.
• #10012: The File extension of the template and the output file do not match
• #10020: Collection was modified; enumeration operation may not execute.
• #10066: Compact NX5 surge testing halted
• #10069: Timeout time configurable ADC
• #10077: System calibration: Reference attenuation: Highest frequency is sometimes 150 instead of inline with the measurements
• #10081: Mini-Circuits SSG-6001RC generates a higher carrier level than the requested 0.0 dBm
• #10122: Marconi 2024 (ID1092) - Error 151: Query UNTERMINATED
• #10133: Keysight Technologies N9322C: EMC Option is not present in this device.
• #10140: Correct keywords for Pulsed Immunity SURGE MB?
• #10166: RE: TDEMI X6: Invalid parameter value.

RadiMation version 2019.1.3

• #8139: Updating consistency in code
• #8211: Object reference not set to an instance of an object: NoStacktrace.
• #8671: RI Fixed power Printout stepsize is incorrect when frequency list used.
• #8760: The CheckDevice check for Amplifier Research amplifiers using the P0/P1 command set is always successful
• #8828: Virtual/manual device driver for EFT
• #8868: VDI Test not running correctly
• #8898: RepGen .xlsx EUT attachment ||EUT|ATTACHMENT 1 CONTENTS||
• #8940: External modulation option for signal generator disappears with RadiMation Free
• #9072: Receiver (ID1691) Input 2: Specific System Error: -200,"Execution error; Function not available; ABORT
• #9083: RBW values are not working for ESU 8
• #9083: Unable to set device driver auto value for measure time, incombination with RBW value
• #9137: Driver: Mini-Circuits SSG-6001RC
• #9257: Update the contents of the RadiLog page on the RadiWiki
• #9391: Object reference not set to an instance of an object: Main Ticket.
• #9554: em test PFS500
• #9757: test interrupted and restarted with wrong RBW and wrong turntable sequence
• #9764: Crash when creating an EUT using the auto-EUT-naming feature.
• #9848: R&S ZNB device driver should not transmit measurement frequencies again when they are not changed
• #9859: EF01003 (FSU 26) LAN ??? 10.49.58.154: Specific System Error: -200,"Execution error;Function not available;BAND:AUTO ON""
• #9880: Radimation hangs during closing, when it is waiting on an errornous amplifier
• #9928: Amplifier Research 150W1000 (Remote controlled): Device Not Connected.
• #9937: Driver: RadiLink new relais
• #9941: Missing Radi Errors descriptions
• #9942: Incorrect frequency in error?
• #9945: Driver: R&S NRX
• #9948: Exception has been thrown by the target of an invocation, when EUT Monitoring channel is opened
• #9950: Controlling a device over HTTP causes unnecessary delays
• #9952: Rohde & Schwarz FSL 3: Specific System Error: -113,"Undefined header;INP:PRES:STAT ON"\n
• #9963: RadiMation crashed during setup AD converter
• #9979: CE: Virtual device - Device not ready
• #9986: Turntable go back to 0deg instead of continuing rotation to 360?? after interrupting test
• #9991: Change Canoe Switch matrix driver so that you can choose which application it starts
• #9992: No error messages are retrieved from Mini-circuits PWR-6GHS
• #9993: Antenna stays at the last position
• #10001: Constant timeout errors with AD-readout
• #10009: Driver: Schwarzbeck TK9420
• #10013: Driver: Anritsu MS2601A as powermeter
• #10018: Check for UNCAL after a Factory Reset of R&S Receiver
• #10023: AntennaTower: Does not return to base position after test in version 2018.2.9
• #10039: Unable to set RBW value
• #10040: Low band of RSS2010B is not measuring the fieldstrength correctly
• #10066: Compact NX5 surge testing halted
• #10068: Show all available ad channels instead of the first 8

RadiMation version 2019.1.2

• #7201: VDI: Reopening TSF still causes error with different location types.
• #8309: The magnetic field current is not shown in multiband immunity.
• #9686: Calibration method of the a multiband immunity test cannot be retrieved in the report.
• #9691: Reference level is not changed to 125 dBuV on a R&S ESU
• #9763: Index out of range when entering description in testlevel auto filter box.
• #9780: Antenna scan calibration in combination with network analyser should use S21
• #9841: Update Visual Studio C++ compiler to 15.9.5
• #9842: ErrorReport: "Spectrum Analyser (ID1691) Input 2: Specific System Error: -200,"Execution error; Function not available; FREQ:STOP:LINK START""
• #9860: Object reference not set to an instance of an object.
• #9901: Could not load file or assembly 'System.ValueTuple, ....' or one of its dependencies.
• #10051: em test VDS 200Q: Sting error: error in data-transmission
• #10093: CE-MB test: not the exact peak is chosen which results in a large measurement error

RadiMation version 2019.1.1

• #1924: Zooming in the graph is not possible in compression test
• #4370: TSF file is duplicated
• #4670: Building the 'TestSites' menu can take a long time
• #4777: Printing the angle plot of a Multiband emission test is printing the frequency graph
• #5754: Graph of UFA calculation starts at -1, but should start at 0
• #6529: Version numbers in the Device driver DLL's should use the build number that is used, also if adjusted to the SVN revision
• #8613: If auto-save is active, data of measurement should be saved to disk when automatic mode is left
• #7793: Compression Gain System Calibration representation of graph is vague
• #7794: Compression Gain System Calibration when saved it removes rest of suggested name description after any.
• #7795: Compression Gain Test default value of added compression point is invalid
• #7869: Y axis scaling in graph improvements
• #8021: When a Band has been selected the TSF is marked as being changed
• #8024: Magnifier in directory configuration is opening wrong folder or not opening the folder, but after multiple clicks it is opening the selection window
• #8148: Modification to Monitoring input channel sometimes reset the configured channel to 1
• #8149: Graph Customization Configuration of the global graph color settings outside a test is not updating the global settings
• #8158: Multiband Emission TSF configuration is not using the maximum number of selectable detectors
• #8220: Graph customization is not applied when a test is opened
• #8265: Confirmation message is default selecting wrong answer (No) instead of Yes
• #8268: Graph Customization is not updated
• #8272: General Information in a calibration file cannot be shown if the calibration file is readonly
• #8277: Disconnecting one VI of four connected RadiCentre devices is raising errors
• #8283: A 'Copy to Clipboard' action is marking a COR file as being changed
• #8290: System Calibration Attenuation / Gain Message shows message to connect the sensor power, but requires a forward powermeter in test equipment
• #8318: Impossible to remove graph line from different test data when the file has been closed
• #8319: Multiband shows an unexpected frequency graph line and table information which can't be removed
• #8374: Multiple PC's running the same confdvdr location gives error
• #8380: Selecting a field probe in a testsite takes more than 20 seconds
• #8546: Index was out of range. Must be non-negative and less than the size of the collection.
• #8554: Ability to show polar plot of field strength in Multiband Immunity test
• #8563: Not possible to select 1 point per row in UFA calculation
• #8564: ErrorReport: "Index was outside the bounds of the array.
• #8587: Changing graph customizations is not setting the changed state of the test
• #8678: Allow 1 port network analyzer calibration for the Agilent 8753
• #8733: Adding a multiline note field in the general information items of the eut is not possible
• #8757: Not possible to edit MB EFT test from the sequence window
• #8812: Wrong lines are drawn in the Multiband Immunity graph, when the same frequencies are tested often
• #8820: Ability to use Spectrum analyzer for harmonics measurements
• #8864: Graphs of gain compression calibration are not showing all the data
• #8866: No error is raised when the fieldprobe has a multiply correction file attached with values below 0
• #8881: Graphs of amplifier linearity calibration cannot be shown in Watts unit
• #8882: Better auto scaling for the y-axis of the amplifier linearity graphs
• #8887: RadiMation free Virtual powermeter
• #8892: Wrong title Harmonics calibration
• #8893: Harmonics test graphs does not use stored graph settings
• #8904: Suggested filename for the calibration is not correct if the TSF contains a .
• #8918: print graph shows temp document already being used by another process
• #8938: Perform antenna scan calibration using a network analyzer instead of signal generator and spectrum analyzer
• #8941: ctlEvents.cs is included twice and seems to be duplicated
• #8948: Not all calibration tests are listed in the add test function of the sequence.
• #8974: Selecting multiple bands with shift is not working as it should be
• #9013: Sort the names of the graph as they are shown below the 'Graphs' button
• #9025: Table tab does not display its measured values in a correct manor
• #9032: Harmonics show -1000dBm
• #9062: Measurement of Harmonics with 2 power meters
• #9082: RadiMation calibration expire date database error crash
• #9100: Object reference not set to an instance of an object: clsGraphElements.FilterShownGraphElements
• #9105: GetGlobalizedHashCode Object must be of type String
• #9125: Pressing update in graph config does not update the image.
• #9137: Driver: Mini-Circuits SSG-6001RC
• #9185: Unclear time logging behaviour Radimation
• #9186: Suggested filename of a calibration file is only 'm.cal' if the TSF description is: "80-1000 MHz, 10 V/m"
• #9188: Corrupt testfile, no data is visible in the graph
• #9218: Infinit loop graph elements being added for gain calibration test
• #9219: Cannot find the device driver - (Device is not on - Device driver is installed)
• #9232: Emission peak number not correct
• #9239: When starting an isotropy measurement the angle tab is not displayed
• #9242: Exception is shown when EUT Monitoring input is opened
• #9248: Readonly Network Analyzer system calibration still has some fields enabled
• #9250: Number of sweeps in TSF of Network Analyzer EUT Calibration is not correctly initialized
• #9267: Continue button does not work
• #9287: Test data disappeared
• #9288: PEAK TABLE keyword no longer works.
• #9291: Save error report standard suggests .log extension
• #9292: When there is no EUT there is no log file in the error report
• #9299: Polar graph displays a graph line that has it's visibility tuned off
• #9303: ErrorReport: "Radimation crashes suddenly after CE measurement is finished "
• #9304: Exception of type 'System.OutOfMemoryException' was thrown.
• #9310: Testdata again not visible.
• #9311: Test data lost / not visible
• #9315: Auto Backup of RadiLog
• #9353: Popup menu of available devices has no seperator between the actions and the devices
• #9356: Configurable AD Converter value always 0
• #9357: Driver: new RadiSense 10 models
• #9384: Index out of range: clsGraphElements.HideElement.
• #9427: Cancel button of Multiband Immunity TSF window is not working anymore
• #9429: Destination array was not long enough
• #9431: External FM modulation waveform is not saved
• #9445: Battery radisense error, amp did not stop generating 100 vm
• #9449: Object reference not set to an instance of an object: clsImpedanceTableCalculation.GetResistanceFromImpedanceTable(
• #9452: Burst, graph does not re-scale when the to measure time is < measured time
• #9453: Close RadiMation with FieldSensor open and connected gives error
• #9454: Object reference error when switching tabs in Configuration window
• #9460: Closing Virtual Forward Power Meter window shows error: Power Meter Init count: 1
• #9465: Carrier frequency control is not correctly sized on the VI Signal generator window
• #9496: Use default graph customization disables controls
• #9504: Report Generator: date format wrong
• #9507: Input string was not in a correct format.
• #9523: Keyword PEAK TABLE does not work in 2018.1.4
• #9533: Power Burst graphs are not correctly shown
• #9535: Configuring a multiband test has a slow response
• #9567: Table is turned after last peak measurement
• #9600: Object reference: Invoke RaiseProgressChangedEvent
• #9634: Isotropy positioner is not being initialized at first angle at the begin of the test.
• #9635: Sudden shutdown without warning.
• #9637: The question 'Are you sure you want to close the test' is shown twice.
• #9638: Opening a small amplifier linearity test result is taking minutes
• #9639: Measure time and step frequency controls are not enabled correctly in RE Multiband when switching testsites
• #9653: Driver: CDN - MEB M5/25A
• #9657: App. Note 115: How to measuring Amplifier harmonics using RadiMation.
• #9658: RM 2018.1.3 crashes often, with object reference not set
• #9687: Multiband EFT is very difficult to close when the automated test is finished
• #9694: External Modulation options not always shown
• #9714: Deadlocking in clsDataIdentifiers.
• #9715: Move during measurement is not shown
• #9719: Polar plots don't scale correct.
• #9731: New sweep in a Multiband Emission test is not overwriting the previous sweep
• #9732: Testdata of a singleband immunity test is not saved at the end of a test
• #9734: Index out of bounds when shift clicking on a band.
• #9742: Changing a sequence file does not work correctly.
• #9753: Driver: Rohde & Schwarz switch matrix OSP230 Frame F01 with options OSP-B133, OSP-B104
• #9795: Object reference not set to an instance of an object.
• #9819: Fix all warnings in the RADDOCS project
• #9820: Fix all warnings in the RADTESTS project
• #9821: Fix all warnings in the RADIMAT project
• #9822: Fix all warnings in the RADEMITESTS project
• #9823: Fix all warnings in the INTERPOLATIONCHART project
• #9824: Fix all warnings in the SAVEUNICODEFILETESTS project
• #9825: Fix all warnings in the INTERPOLATIONTESTS project
• #9826: Fix all warnings in the RADSTDCLTESTS project
• #9827: Fix all warnings in the HTTP_POST project
• #9838: Crash during report generation
• #9855: Set all C# projects to 'Treat all warnings as error' to 'All'
• #9874: This is not a valid action for the end of a row.
• #9877: Radiated emission bandwidth is not correctly displayed in 2019.1.1
• #9884: EUT window not visible
• #9891: Table is not visible during test
• #9897: Too much limitlines in MB RE is causing radimation to get slow and hang
• #9922: Driver: AR250S1G6M1 Amplifier
• #9923: Driver: Coupler, Amplifier Research: DC7230A
• #9924: Driver: Amplifier AR5000A225A
• #9961: Incorrect bandwidth in report for CE and RE
• #10019: IF Overload is detected ESU26.